New BLHELI32 ESC with F3 MCU, give more smooth control and faster responding speed. Supports up to 80A burst and 65A continued. (ESC mounted under props, without anything covered on the ESC)
F3(M4 Coreted at 4S 65A, under props, nothing covered for 1min
18 x 27 mm
Supports Lipo 3-6S
Ext. cap needed for 6s (220uf 35v for 6s usage.)
Onboard WS2812B LED
Wei) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz
Mosfet tesght: 4.4g (1pcs)
Kakute F7 AIO V1.5
The Holybro Kakute F7All-In-One flight controller makes it easy to build your multirotor. It integrates flight controller (FC), power distribution board (PDB), and on-screen display (OSD) in one. The Kakute F7 AIO's layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy. IMU updated to MPU6000,Re-designed and more reliable damping structure
Supports Betaflight, Butterflight.
Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and accelerometer.
Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
2 oz. copper PCB allows up to 120A maximum continuous current.
Dedicated bootloader button for easy firmware flashing.
Low-profile design fits into even very compact frames.
Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "B+" pad only).
Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 AIO monitors voltage directly from the battery power lead.
Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
Supports BLHeli pass-through for easy ESC upgrade and configuration.
MCU: STM32F745 32-bit processor
IMU: MPU6000 (SPI)
Current Sensor: Approximately 130 amps maximum measurable value
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without "uninvert hack".
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging
Dimensions: 35x48x7mm (includes foam-mounted gyro board in height)
Mounting Holes: Standard 30.5mm square to center of holes
Atlatl HV V2
Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc. Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband. SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more. All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used. MMCX connector is durable and easy to use. Rated for 100's of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors. LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad. Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle. 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air. Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly. Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.
Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW Audio: 6.5 MHz Mono Antenna Connector: MMCX Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts Dimensions: 35x25x7mm (Includes USB height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 9.3g
Kakute F7 AIO+Atlatl V2 stack *1
Tekko32 F3 Metal ESC *4
80mm SMA--MMCX Cable *1
150mm 4pin JST GH wire *1
Electrolytic capacito: 220uF 35v *4
24AWG 100mm Black wire *1
24AWG 100mm White wire *1
24AWG 100mm Blue wire *1
16AWG 100mm Red wire *1
16AWG 100mm Black wire *1
BLHeli_32 ESC Firmware Overview
Recently Viewed Items
You may also like
GET 10% OFF!
Sign up to save 10% off your first order!
Or 6 weekly interest free payments from
$80.66today & 5 weekly interest free payments of
$240.00 withwhat's this?